|
FW Murphy Centurion 可配置控制器
Centurion 主要设计用于发动机/电动机驱动的压缩机，非常适合使用标准配置的许多控制应用，以节省资金并减少培训。此外，FW Murphy 还专注于定制设计控制包，以满足各种应用的精确规格。
Centurion C5 控制器持续监控输入信号、设定点和命令输出以保持正常运行，当发生超限事件时，将停止、关闭或控制设备以改变条件。Centurion 的自动启动功能允许根据压力设定点或数字信号等参数启动/停止。
Centurion 通过通信端口向连接的显示器和任何远程监控系统提供实时数据，并通过以太网和串行方法。
Centurion? 可配置控制器
Centurion C5 可配置控制器是 Centurion 控制和监控系统的核心。C5 控制器通过诊断使用户处于控制之中，从而减少故障排除、改善通信并增强数据管理。
完全可配置的控制和监控系统，适用于往复式/螺杆式压缩机和泵系统
可扩展系统，可满足大多数三级或四级压缩机应用
使用基于 Windows 的软件进行用户可配置性允许操作员指向并单击以实施标准流程，并在获得授权时配置 I/O 点
无需编程经验
本地和远程通信，通过 RS485/232/以太网的 Modbus RTU
USB 1.1 / 2.0 支持无串行端口的笔记本电脑
配置和设定点的上传/下载功能
关闭历史记录列表（最近 20 个事件）
事件历史列表（过去 32 场活动）
活动警报列表
10 个可配置的维护计时器
运行小时计
支持使用润滑器脉冲的无流量累加
短周期启动保护/每小时启动（电动机）
8 个控制回路（ISA、PID 或线性）
提供简单易用的配置模板
存储在非易失性闪存中的配置
设定点存储在非易失性EEPROM存储器中
生产可编程，CS&S可以修改以满足客户要求，无需工程支持
支持CAN，支持电子引擎
一个核心模块，适用于标准和定制应用
DIN导轨安装
在一个 M-View? 触摸屏显示器上查看 EICS 和 Centurion 系统
能够将旧的 Centurion LCD 显示器升级到 M-View，以获得更高的分辨率、更少的滚动和更亮的背光
减少故障排除的诊断
世界一流的认证和统一的国际标准
面向未来且向后兼容
所有非易燃输入
压缩机杆负载计算、报警和停机
Primarily designed for engine/electric motor driven compressors, the Centurion is well suited for many control applications using standard configurations to save money and reduce training. Additionally, FW Murphy specializes in custom designing control packages to meet exact specifications for a variety of applications.
Continuously monitoring input signals, set points and command outputs to maintain proper operation, the Centurion C5 Controller will stop, shut down or control equipment to change conditions when an out-of-limits event occurs. The auto-start capabilities of the Centurion allow for start/stop based on parameters such as pressure set points or by digital signals.
The Centurion provides real-time data via communication ports to a connected display and any remote monitoring system through Ethernet and serial methods.
Centurion? Configurable Controller
The Centurion C5 Configurable Controller is the core of the Centurion control and monitoring system. The C5 Controller puts users in control with diagnostics that reduce troubleshooting, improve communication and enhance data management.
- Fully configurable control and monitoring system with applications for reciprocating/screw compressors and pump systems
- Expandable system to meet most three- or four-stage compressor applications
- User configurability with Windows-based software allows the operator to point and click to implement standard processes, and if authorized, configure the I/O points
- No programming experience required
- Local and remote communications, Modbus RTU via RS485/232/Ethernet
- USB 1.1 / 2.0 support for laptops without a serial port
- Upload/download capabilities for configurations and set points
- Shut-down history list (Last 20 events)
- Event history list (Last 32 events)
- Active alarm list
- 10 configurable maintenance timers
- Run hourmeter
- Support for no-flow totalization using lubricator pulses
- Short cycle start protection / starts per hour (electric motor)
- Eight control loops (ISA PID or Linear)
- Configuration templates provided for simple use
- Configurations stored in non-volatile flash memory
- Set points stored in non-volatile EEPROM memory
- Production Programmable, CS&S can modify to meet customer requirements without engineering support
- CAN capable, to support electronic engines
- One core module for Standard and Custom applications
- DIN Rail Mountable
- View EICS and Centurion systems on one M-View ? Touch screen display
- Ability to upgrade your older Centurion LCD display to the M-View for higher resolution, less scrolling and brighter backlight
- Diagnostics that reduce troubleshooting
- World-class certifications and harmonized international standards
- Future-proof and backward compatible
- All non-incendive inputs
- Compressor Rod Load calculation, alarm and shutdown
|
